Find a sidewalk contractor near Bryan, TX

Because unsealed concrete is porous, it readily absorbs liquids, leading to unsightly stains and freeze-and-thaw cycle damage. For this reason, it’s important to seal concrete that will see spills or outdoor weather.

The best option for garage floors and other high-traffic areas is epoxy, which forms a hard and extremely durable surface on top of concrete. Epoxy, acrylic, and polishes are often used on indoor floors, while acrylic-resin sealers and reactive penetrating sealers are used on outdoor surfaces to repel water and salt. Locate a concrete contractor in your area to help find the best solution.

Paving contractors can be hired to install a concrete or asphalt driveway at your home, office or property. They can also repave an asphalt or concrete driveway that has been damaged by time, weather or heavy loads. When you are looking for a driveway contractor, request quotes from at least three professionals who are in good standing and have great customer reviews. They should do a site visit and write you a bid, detailing the work involved, materials needed, approximate length of the project and estimated cost.

The site for your new driveway will determine costs and the work required for your contractor. First, the ground must be excavated to lay a clear path. This means removing any trees, bushes and stumps. Next, the driveway contractor will grade the area, making a level surface for the concrete or asphalt. To ensure proper drainage, driveway contractors should install a sub-base of compacted gravel (or similar) 4 inches-8 inches deep, depending on your soil type. Then the concrete or asphalt may be poured and smoothed over the top. Your driveway contractor should recommend an appropriate sealant for your climate and advise you on curing time. When hiring a paving contractor, check out our tips for smart hiring on Thumbtack.

A concrete paint cover is typically opaque and covers up the color of the concrete. This means it provides significant protection to the concrete below. However, if it is improperly applied or subjected to heavy traffic, a painted concrete floor is likely to chip and peel. 

Epoxy and staining are two types of concrete floor sealer. Epoxy is a more durable but often more expensive option than a concrete stain. Epoxy forms a protective layer, while concrete stain is more decorative and requires more maintenance. Because epoxy can be more expensive than concrete stain, it is best used in high-traffic areas or in applications where low maintenance is desired.

A concrete stain, on the other hand, is quick to apply and can show off the textures of the concrete, but it does not provide a high degree of protection for the concrete against spills, salt, water and other contaminants. Staining concrete generally requires a dust mop, a pH-neutral cleaner and water to clean, while epoxy can cause resin buildup that necessitates the use of special detergents.

Find a concrete contractor near you for help selecting the right floor concrete sealer.

Concrete contractors can build foundations, structures, driveways, concrete storm drains, raise or level concrete patios and much more. They can handle every step of the process, starting with framing the mold that the concrete is poured into. They then cut, assemble and tie together the rebar, giving the concrete its tensile strength. Finally, they pour the concrete in, mixing and conditioning it to ensure it cures properly. They will also take steps to ensure that no air pockets are trapped within it. 

If you have a project that requires the help of a concrete contractor, reach out to one today to get a price estimate.

 Here are some examples of average costs:

• The national average cost to hire a concrete specialist is $2,750, but that price can vary greatly depending on the work needed to repair and resurface your concrete driveway, the square footage of the project, current costs of concrete, and regional labor rates.
• Driveway contractors average $2-$3 per square foot to smooth and resurface your asphalt driveway.
• Resurfacing concrete driveways averages $3-$10 per square foot. Pricing can depend on repairs needed, project size and geographic location.
• Nationally, the average cost for resurfacing a 500-square-foot driveway ranges from $2,000 to $5,000.
• Sealant for a concrete drive can cost $20-$80 per gallon.
• Sealant for an asphalt drive averages 25 cents per square foot.

The best finish for concrete floors depends on your personal taste. An acid stain is a bold, varied look with lots of texture and the potential for earthy tones and a natural stone appearance. A water-based stain might not last as long as an acid stain, but it gives you the choice of many different colors. Epoxy is great for high-traffic areas, kitchens, bathrooms, basements and garages. It provides a glossy, damage-resistant, non-slip coating on your concrete floors. To find out which finish is the best for your concrete floors, contact a concrete contractor near you.

To find the best concrete contractors in your area, start by comparing concrete contractor reviews and ratings, which can give you insight into the quality of work you can expect from potential concrete contractors. When reading reviews, pay attention to details about how long the project took and whether the customer had any disputes with the contractors. The reviews often contain photos of past work, but if you don’t see any reviews, ask the contractor to share photographs of concrete floors, driveways and other projects they’ve worked on. Look for details such as clean edges and a lack of cracking. And finally, if a concrete license is required in your state, ask to see the contractor’s credentials. 

Yes, concrete floors are generally more affordable than hardwood floors. Generally, a concrete floor costs between $2 and $15 per square foot, while hardwood floors cost between $12 and $20 per square foot, according to Floor Critics. While concrete requires preparation and pouring, its ease of finishing makes it a very affordable flooring option. Choose between finishes like acid stains, epoxy and more. While hardwood is not cheap flooring, it offers warmth and durability with infrequent maintenance.

If you're stuck between installing wood floors or concrete floors, reach out to a flooring installation professional near you. 

Masonry contractors build structures with smaller units like bricks and stones, binding them together with mortar to form a larger structure. Concrete contractors, on the other hand, only use concrete to form structures. This mixture of cement, water and other materials is poured into a premade structure and left to cure, forming a single structure made on one part.

Call a concrete contractor near you to replace or repair concrete floors. You can also find concrete masonry contractors in your area to help you with other projects.

Hire concrete contractor services for projects such as concrete foundations, concrete driveways, slab floors and other concrete work. A concrete contractor builds structures from concrete, often handling every step of the process from mixing ingredients to building the retaining structure to pouring and settling the mix. This individual or team supervises delivery and pouring to ensure that it’s done correctly. Many states require concrete contractors to have a license.

Paving contractors can be hired to install a concrete or asphalt driveway at your home, office or property. They can also repave an asphalt or concrete driveway that has been damaged by time, weather or heavy loads. When you are looking for a concrete driveway contractor, request quotes from at least three professionals who are in good standing and have great customer reviews. They should do a site visit and write you a bid, detailing the work involved, materials needed, approximate length of the project and estimated cost.

The site for your new driveway will determine costs and the work required for your contractor. First, the ground must be excavated to lay a clear path. This means removing any trees, bushes and stumps. Next, the driveway contractor will grade the area, making a level surface for the concrete or asphalt. To ensure proper drainage, driveway contractors should install a sub-base of compacted gravel (or similar) 4 inches-8 inches deep, depending on your soil type. Then the concrete or asphalt may be poured and smoothed over the top. Your driveway contractor should recommend an appropriate sealant for your climate and advise you on curing time. When hiring a paving contractor, check out our tips for smart hiring on Thumbtack.